For general maintenance that requires high torque values and repeatable results, the Edge is HYTORC’s workhorse. The straightforward three-moving-part design was created by HYTORC over 30 years ago and has been consistently improved upon resulting in the most tried and tested line of hydraulic torque wrenches in the world.
good torque wrench


The three-moving part design of the Edge series reduces the number of potential repairs and keeps operating costs to a minimum.
industrial torque tools
industrial torque tool


The multi-axis swivel is used on all HYTORC hydraulic torque wrenches (with the exception of the ICE series) for maximum positioning flexibility and safety.
torque tool set


For quick and simple directional changes and maximum durability, the Edge series features a push through square drive.
good torque wrench


  • Torque Charts Open or Close
  • Technical Data Open or Close



    TOOL MODEL Height (H) Width (W) Length (L) Radius SQ Weight Torque Range
    EDGE-.5 2.95" 1.64" 4.01" 0.82" ¾" 3.3 Lbs. 106 - 710 ft-lbs
    EDGE-2 3.53" 1.97" 4.94" 0.97" ¾" 4.05 Lbs. 178 - 1,257 ft-lbs
    EDGE-4 4.71" 2.63" 6.4" 1.31" 1" 8.50 Lbs. 443 - 3,079 ft-lbs
    EDGE-6 6.04" 3.18" 7.61" 1.57" 1 ½" 19.2 Lbs. 893 - 6,241 ft-lbs
    EDGE-8 6.57" 3.57" 8.67" 1.86" 1 ½" 20.05 Lbs. 1,230 - 8,555 ft-lbs
    EDGE-12 7.07" 3.95" 9.56" 1.96" 1 ½" 25 Lbs. 1,615 - 11,291 ft-lbs
    EDGE-30 10.10" 5.64" 13.71 2.79" 2 ½" 64.7 Lbs. 4,448 - 29,650 ft-lbs
  • Troubleshooting Open or Close
    Prior to testing hydraulic torque wrenches. A visual inspection should be done. The visual inspection should include.
    1. Cracked, bent, or damaged couplers.
    2. Swivel Assembly
      • Cracked swivel block
      • Loose swivel assembly
      • Swivel post retaining ring is attached
    3. Loose end cap
    4. Cracked or damaged housing
    When testing hydraulic torque wrenches. Make sure the pump functions correctly, and is set to 10,000 PSI before the tool is connected. Connect the tool to the hose, and test the tool using the pump remote. ADVANCE and RETRACT the tool several times. Make sure the tool functions properly and the pump pressure builds 10,000 PSI / 700 BAR in the ADVANCE position.
    Tool does not ADVANCE or RETRACT. Check the following.
    1. Couplers are loose or damaged.
      • Tighten and/or replace couplers.
    2. Ratchet
      • Replace ratchet if the teeth are stripped, missing or damaged.
    3. Drive pawl Assembly
      • Check drive pawl springs for damage.
      • Inspect drive pawl for damage.
    Tool does not build 10,000 PSI in the ADVANCE position, and there are no external leaks. The tool has an internal leak. Internal leaks are located in two areas, the swivel assembly and the cylinder.
    1. Swivel Assembly - Tool will not build over 2000 PSI
      • Replace damaged swivel seals.
      • Inspect swivel post for wear and/or damage.
      • Inspect swivel block for damage.
    2. Cylinder - Tool will not build over 6000 to 7000 PSI
      • Check the piston and cylinder O-ring for wear and/or damage.
      • Inspect the piston assembly for wear and /or damage.
      • Inspect cylinder wall for excessive wear.
    Tool has an external leak.
    1. Swivel Assembly
      • Bent or broken couplers.
      • Worn and/or damaged seals.
      • Cracked or damaged swivel block.
      • Damaged swivel post.
    2. Cylinder
      • Worn and/or damaged seals.
      • Loose end cap.
      • Worn and /or damaged piston assembly.
      • Damaged housing assembly.
    The tool's square drive rocks back and forth. Check the following.
    1. Lever Assembly
      • Lever mounting screws are too tight.
      • Levers cracked and/or damaged.
    2. Reaction Pawl Assembly
      • Damaged reaction pawl spring.
      • Damaged reaction pawl.
    3. Ratchet
      • Replace the ratchet if the teeth are stripped, missing or damaged.
  • Operations Manual Open or Close


Backup Wrenches Interchangeable spanners from 1-7/16" to 3 1/8".
Extended Reaction Arm Long reach version of the standard reaction arm
Sockets High strength and impact resistant hex and Allen sockets.
Reaction Sleeve Reaction sleeve used on our MXT and Edge line of tools.